The short answer
Why is my furnace running but the house is still cold?
The blower is moving air, but that air either isn't being heated or isn't reaching your rooms. In most homes it comes down to one of five things: the thermostat fan is set to ON, a clogged filter is tripping the furnace's safety limit, the burners aren't staying lit (dirty flame sensor or failed igniter), the condensate drain is blocked, or heated air is leaking out of the ductwork before it gets to the vents.
Before you call
5 checks to do first
These take about ten minutes and rule out the simple causes before you pay for a service visit.
Thermostat: HEAT, fan on AUTO
If the fan is set to ON, the blower runs nonstop and pushes unheated air between cycles. Switch to AUTO, set the temperature 5° above the room reading, and replace the batteries if the screen is dim.
Pull the air filter
Hold it up to a light. If you can't see through it, replace it. A plugged filter makes the furnace overheat, the burners shut off, and the fan keeps blowing cool air.
Open vents, clear the returns
Open every supply register and move furniture, rugs and boxes off the return grilles. Closing vents in unused rooms raises pressure and can trip the same safety limit.
Breaker and furnace switch
Reset a tripped breaker once. Find the light-switch-style power switch on or near the furnace and make sure it's on. If the breaker trips again, stop and call.
Watch one full startup
Turn the heat up and stand at the furnace. Note whether the burners light, how long they stay lit, and whether a small light on the control board is blinking a pattern. That information saves the technician time and saves you money on diagnosis.
Diagnose it
7 common causes, by what you're seeing
Match the symptom to the likely cause. Two are homeowner fixes. The rest need a technician with a meter.
Stop and get out if:
- You smell gas. Leave the house, then call 911 or your gas utility from outside. Don't flip switches on your way out.
- A carbon monoxide alarm is sounding. Get everyone outside and call 911. CO has no smell, so treat the alarm as real even if the furnace seems fine.
- You see scorch marks, melted wiring or smoke at the furnace. Shut it off at the breaker.
Checked everything and it's still cold?
Tell us what the vents feel like and what you saw at startup. We'll get a local tech scheduled.
Call (417) 929-5942Local conditions
Why this happens so often in Springfield and the Ozarks
Southwest Missouri weather swings hard. A 60° afternoon can turn into a night in the teens, and a furnace that coasted through October suddenly has to run long cycles. That is when a filter that was "fine" last week starts tripping the limit switch, and when a weak igniter finally quits.
Two local patterns come up a lot. Older homes in central Springfield often have ductwork in crawl spaces, where a loose joint dumps heated air under the floor instead of into the room. And many all-electric homes around Ozark, Nixa and Republic heat with heat pumps, which depend on backup heat strips once it gets cold. When those strips fail, the system runs all night and the thermostat keeps dropping.
Areas served
- Springfield
- Ozark
- Nixa
- Republic
- Battlefield
- Willard
- Rogersville
- Strafford
FAQ
Common questions
Is it safe to keep running the furnace if it isn't heating?
If you smell gas or a carbon monoxide alarm sounds, leave the house and call 911 or your gas utility from outside. Otherwise, if the burners keep shutting off or the air stays cold after the basic checks, turn the system off at the thermostat and call a technician rather than letting it cycle for hours.
Can a dirty filter really make the furnace blow cold air?
Yes. A clogged filter starves the furnace of airflow, the heat exchanger overheats, and a safety switch shuts the burners off. The fan keeps running to cool the unit, so you feel cool air from the vents.
My heat pump runs constantly and the house is cold. Is that the same problem?
It's a related one. Heat pumps lose capacity as outdoor temperatures drop and rely on auxiliary heat strips to keep up. If the strips have failed, the outdoor unit is iced over, or refrigerant is low, the system runs nonstop and the house still cools off.
What should I tell the technician when I call?
Whether the air from the vents is cold, lukewarm, or warm but weak. Whether the burners light and then shut off. Any blinking light code on the furnace. When the filter was last changed. And whether the system is gas, electric or a heat pump.
How long should it take the house to warm up?
A healthy system should raise the indoor temperature steadily within the first 15 to 30 minutes of a call for heat. If the thermostat reading is flat or falling after an hour of run time, something is wrong.